Prof. Dr. ADEM ÇİÇEK

Yayın Ağı

Makaleler 72

1. A novel chatter-resistant boring bar design with lattice structure and non-Newtonian fluid

ÖZKAYA E., Aslantas K., Çetindağ H. A., ÇİÇEK A.

Journal of Manufacturing Processes , cilt.178, ss.155-168, 2026 (SCI-Expanded, Scopus)

2. Effect of overhang distance and tool geometry on chatter in boring of Ti-6Al-4 V alloy

Çetindağ H. A., Aslantas K., ÖZKAYA E., ÇİÇEK A.

Journal of the Brazilian Society of Mechanical Sciences and Engineering , cilt.48, sa.6, 2026 (SCI-Expanded, Scopus)

3. Thermo-Mechanical Analysis and Fatigue Life Estimation of Shrink-Fit Tool Holders

Aslantas K., ÖZKAYA E., ÇİÇEK A.

Machines , cilt.14, sa.4, 2026 (SCI-Expanded, Scopus)

4. Effect of geometric parameters on the vibration performance of polymer honeycomb structures produced by additive manufacturing Eklemeli imalatla üretilen polimer bal peteği yapıların titreşim performansına geometrik parametrelerin etkisi

Kızılkaya U., Aslantas K., Özkaya E., ÇİÇEK A.

Journal of the Faculty of Engineering and Architecture of Gazi University , cilt.41, sa.1, ss.495-506, 2026 (SCI-Expanded, Scopus, TRDizin)

5. Characterization of the friction behavior of wrought and hot isostatic pressed laser powder bed fusion Ti6Al4V alloys

UÇAK N., Aslantas K., ÇİÇEK A., Outeiro J.

CIRP Journal of Manufacturing Science and Technology , cilt.63, ss.83-96, 2025 (SCI-Expanded, Scopus)

6. Review of chatter control techniques in turning and boring

Çetindağ H. A., Oezkaya E., ÇİÇEK A., Aslantas K.

International Journal of Advanced Manufacturing Technology , cilt.139, sa.11-12, ss.5363-5407, 2025 (SCI-Expanded, Scopus)

7. Numerical analysis of the influence of sequential cuts during micro-milling of wrought and LPBF Ti6Al4V alloys

UÇAK N., Outeiro J., ÇİÇEK A., Aslantas K.

Manufacturing Letters , cilt.44, ss.622-630, 2025 (ESCI, Scopus)

8. Integration of Lattice Structures into the Boring Bars as a Passive Chatter Suppression Technique: Concepualization, Modelling and Simulation

Oezkaya E., Aslantas K., ÇİÇEK A., Çetindağ H. A.

Vibration , cilt.8, sa.2, 2025 (ESCI, Scopus)

9. The effects of tool geometry on surface integrity in hard turning of ball bearing inner raceways

Sağır G., ÇİÇEK A., Müştak O., SARIKAVAK Y.

Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering , 2025 (SCI-Expanded, Scopus)

10. Investigation of the effects of heat treatment and hot isostatic pressing in micro-drilling of Ti6Al4V alloy fabricated by laser powder bed fusion

Balcı A., ÇİÇEK A., UÇAK N., Aslantas K.

Precision Engineering , cilt.91, ss.617-631, 2024 (SCI-Expanded, Scopus)

11. Comparative analysis of micro-milling performances of conventionally and additively manufactured Ti6Al4V alloys: Experimental investigation and 3D modelling

Uçak N., Outeiro J., Çiçek A., Aslantaş K.

CIRP Journal of Manufacturing Science and Technology , cilt.51, ss.213-235, 2024 (SCI-Expanded, Scopus)

12. Performance of conventional and wiper CBN inserts under various cooling conditions in hard turning of AISI 52100 steel

Çetindağ H. A., ÇİÇEK A., UÇAK N., Aslantas K.

Materialpruefung/Materials Testing , cilt.66, sa.2, ss.288-298, 2024 (SCI-Expanded, Scopus)

13. An experimental study on ultrasonic-assisted drilling of Inconel 718 under different cooling/lubrication conditions

Erturun Ö. F., Tekaüt H., ÇİÇEK A., UÇAK N., Namlu R. H., Lotfi B., et al.

International Journal of Advanced Manufacturing Technology , cilt.130, sa.1-2, ss.665-682, 2024 (SCI-Expanded, Scopus)

14. Constitutive modelling of Ti6Al4V alloy fabricated by laser powder bed fusion and its application to micro cutting simulation

Uçak N., Çiçek A., Outeiro J., Aslantaş K., Çetin B.

Mechanics of Materials , cilt.185, 2023 (SCI-Expanded, Scopus)

15. Crashworthiness evaluation of hybrid tubes made of GFRP composite and aluminum tubes filled with honeycomb structures

Mert S. K., Güler M. A., ALTIN M., Acar E., ÇİÇEK A.

Journal of the Brazilian Society of Mechanical Sciences and Engineering , cilt.45, sa.6, 2023 (SCI-Expanded, Scopus) Sürdürülebilir Kalkınma

16. Experimental evaluation of tool wear and surface roughness under different conditions in high-speed turning of Ti6Al4V alloy

Uçak N., Aslantas K., Çiçek A.

Journal of Materials and Manufacturing , cilt.2, sa.1, ss.1-10, 2023 (Hakemli Dergi)

17. Effect of Deep Cryogenic Treatment on Microstructure, Mechanical Properties, and Residual Stress of AISI 52100 Bearing Steel

Kara F., ÇİÇEK A., Demir H.

Engineered Science , cilt.26, 2023 (Scopus)

18. Performance evaluation of DLC and NCD coatings in micro-milling of Al7075-T6 alloy

Aslantas K., Hascelik A., ÇİÇEK A.

Journal of Manufacturing Processes , cilt.81, ss.976-990, 2022 (SCI-Expanded, Scopus)

19. Machinability of 3D printed metallic materials fabricated by selective laser melting and electron beam melting: A review

Uçak N., Çiçek A., Aslantas K.

Journal of Manufacturing Processes , cilt.80, ss.414-457, 2022 (SCI-Expanded)

20. DIN 100Cr6 çeliğinin korozyon direnci ve elektrik iletkenliğine kriyojenik işlemin etkisi

KOCABAŞ M., ÇİÇEK A., ÇELİK A. G., GÜNEŞ İ., ASLANTAŞ K.

JOURNAL OF CHARACTERIZATION , cilt.2, sa.2, ss.167-175, 2022 (Hakemli Dergi)

21. Performance of Multilayer Coated and Cryo-Treated Uncoated Tools in Machining of AISI H13 Tool Steel—Part 1: Tungsten Carbide End Mills

ÇİÇEK A., Kıvak T., EKİCİ E., Kara F., UÇAK N.

Journal of Materials Engineering and Performance , cilt.30, sa.5, ss.3436-3445, 2021 (SCI-Expanded, Scopus)

22. Performance of Multilayer Coated and Cryo-treated Uncoated Tools in Machining of AISI H13 Tool Steel—Part 2: HSS End Mills

ÇİÇEK A., EKİCİ E., Kıvak T., Kara F., UÇAK N.

Journal of Materials Engineering and Performance , cilt.30, sa.5, ss.3446-3457, 2021 (SCI-Expanded, Scopus)

23. Machinability evaluations of austempered ductile iron and cast steel with similar mechanical properties under eco-friendly milling conditions

Eraslan D., Balcı A., Çetin B., UÇAK N., ÇİÇEK A., Yılmaz O. D., et al.

Journal of Materials Research and Technology , cilt.11, ss.1443-1456, 2021 (SCI-Expanded, Scopus)

24. The effects of CryoMQL conditions on tool wear and surface integrity in hard turning of AISI 52100 bearing steel

Çetindağ H. A., Çiçek A., Uçak N.

Journal of Manufacturing Processes , cilt.56, ss.463-473, 2020 (SCI-Expanded, Scopus)

25. The effects of Al2O3 coating on serrated chip geometry and adiabatic shear banding in orthogonal cutting of AISI 316L stainless steel

UÇAK N., Aslantas K., ÇİÇEK A.

Journal of Materials Research and Technology , cilt.9, sa.5, ss.10758-10767, 2020 (SCI-Expanded, Scopus)

26. Investigation of the effects of cryogenic cooling on drilling performance in drilling of Inconel 718 superalloy Inconel 718 süperalasiminin delinmesinde kriyojenik soǧutmanin delme performansi üzerine etkilerinin arastirilmasi

Ucak N., Cicek A.

Journal of the Faculty of Engineering and Architecture of Gazi University , cilt.34, sa.3, ss.1241-1252, 2019 (SCI-Expanded, Scopus, TRDizin)

27. Optimization of process parameters for micro milling of Ti-6Al-4V alloy using Taguchi-based gray relational analysis

Aslantas K., Ekici E., Cicek A.

Measurement: Journal of the International Measurement Confederation , cilt.128, ss.419-427, 2018 (SCI-Expanded, Scopus)

28. An experimental study on relationship between tool wear - slot geometry in micromachining Mikro işlemede takım aşınması - kanal geometrisi ilişkisi üzerine deneysel bir çalışma

ASLANTAŞ K., ÇİÇEK A., Celik S. G.

Journal of the Faculty of Engineering and Architecture of Gazi University , cilt.33, sa.4, ss.1285-1298, 2018 (SCI-Expanded, Scopus, TRDizin) Sürdürülebilir Kalkınma

29. The effects of cutting conditions on cutting temperature and hole quality in drilling of Inconel 718 using solid carbide drills

Ucak N., Cicek A.

Journal of Manufacturing Processes , cilt.31, ss.662-673, 2018 (SCI-Expanded, Scopus)

30. 3D numerical modelling of micro-milling process of Ti6Al4V alloy and experimental validation

UCUN İ., ASLANTAŞ K., ÖZKAYA E., ÇİÇEK A.

Advances in Materials and Processing Technologies , cilt.3, sa.3, ss.250-260, 2017 (Scopus)

31. Taguchi optimization of machining parameters in drilling of AISI D2 steel using cryo-treated carbide drills

AKINCIOĞLU G., Mendi F., ÇİÇEK A., AKINCIOĞLU S.

Sadhana - Academy Proceedings in Engineering Sciences , cilt.42, sa.2, ss.213-222, 2017 (SCI-Expanded, Scopus)

32. AISI 304 ve AISI 316 Östenitik Paslanmaz Çeliklerin İşlenebilirliğinin Değerlendirilmesi

ALTAN ÖZBEK N., ÇİÇEK A., GÜLESİN M., ÖZBEK O.

Politeknik Dergisi , cilt.20, sa.1, ss.43-49, 2017 (TRDizin)

33. Performance of cryogenically treated Cu and CuCrZr electrodes in an EDM process

Cetin A., Cakir G., Aslantas K., Ucak N., Cicek A.

Kovove Materialy , cilt.55, sa.6, ss.431-440, 2017 (SCI-Expanded, Scopus)

34. Application of Deep Cryogenic Treatment to Uncoated Tungsten Carbide Inserts in the Turning of AISI 304 Stainless Steel

ÖZBEK N. A., ÇİÇEK A., Gulesin M., ÖZBEK O.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE , sa.12, ss.6270-6280, 2016 (SCI-Expanded, Scopus)

35. Cutting performance of nano-crystalline diamond (NCD) coating in micro-milling of Ti6Al4V alloy

Aslantas K., Hopa H. E., Percin M., Ucun I., Cicek A.

Precision Engineering , cilt.45, ss.55-66, 2016 (SCI-Expanded, Scopus)

36. Micro-drilling of Ti-6Al-4V alloy: The effects of cooling/lubricating

Percin M., Aslantas K., Ucun I., Kaynak Y., Cicek A.

Precision Engineering , cilt.45, ss.450-462, 2016 (SCI-Expanded, Scopus)

37. Effect of cutting conditions on wear performance of cryogenically treated tungsten carbide inserts in dry turning of stainless steel

Özbek N. A., ÇİÇEK A., GÜLESİN M., Özbek O.

Tribology International , cilt.94, ss.223-233, 2016 (SCI-Expanded, Scopus)

38. Evaluation of wear performance of cryogenically treated Vanadis 4 Extra tool steel

Gunes I., Uzun M., Cetin A., Aslantas K., Cicek A.

Kovove Materialy , cilt.54, sa.3, ss.195-204, 2016 (SCI-Expanded, Scopus)

39. Prediction of cutting temperature in orthogonal machining of AISI 316L using artificial neural network

KARA F., ASLANTAŞ K., ÇİÇEK A.

APPLIED SOFT COMPUTING , cilt.38, ss.64-74, 2016 (SCI-Expanded, Scopus)

40. Effects of Deep Cryogenic Treatment on the Wear Resistance and Mechanical Properties of AISI H13 Hot-Work Tool Steel

ÇİÇEK A., KARA F., KIVAK T., EKİCİ E., UYGUR İ.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE , cilt.24, sa.11, ss.4431-4439, 2015 (SCI-Expanded, Scopus)

41. Optimization of drilling parameters using Taguchi technique and response surface methodology (RSM) in drilling of AISI 304 steel with cryogenically treated HSS drills

ÇİÇEK A., KIVAK T., Ekici E.

JOURNAL OF INTELLIGENT MANUFACTURING , cilt.26, sa.2, ss.295-305, 2015 (SCI-Expanded, Scopus)

42. Effect of Deep Cryogenic Treatment on Wear Resistance of AISI 52100 Bearing Steel

Gunes I., ÇİÇEK A., ASLANTAŞ K., KARA F.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS , cilt.67, sa.6, ss.909-917, 2014 (SCI-Expanded, Scopus)

43. Investigation of the effects of cryogenic treatment applied at different holding times to cemented carbide inserts on tool wear

ÖZBEK N. A., ÇİÇEK A., Gulesin M., ÖZBEK O.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE , cilt.86, ss.34-43, 2014 (SCI-Expanded, Scopus)

44. Vibration analysis of rolling element bearings defects

Saruhan H., Saridemir S., Çiçek A., Uygur I.

Journal of Applied Research and Technology , cilt.12, sa.3, ss.384-395, 2014 (SCI-Expanded, Scopus)

45. Fatigue life predictions of metal matrix composites using artificial neural networks

Uygur I., ÇİÇEK A., Toklu E., Kara R., Saridemir S.

Archives of Metallurgy and Materials , cilt.59, sa.1, ss.97-103, 2014 (SCI-Expanded, Scopus)

46. ANN and multiple regression method-based modelling of cutting forces in orthogonal machining of AISI 316L stainless steel

Kara F., Aslantas K., Cicek A.

Neural Computing and Applications , cilt.26, sa.1, ss.237-250, 2014 (SCI-Expanded, Scopus)

47. Multiple regression and ANN models for surface quality of cryogenically-treated AISI 52100 bearing steel

Kara F., ÇİÇEK A., DEMİR H.

Journal of the Balkan Tribological Association , cilt.19, sa.4, ss.570-584, 2013 (SCI-Expanded, Scopus)

48. Evaluation of machinability of hardened and cryo-treated AISI H13 hot work tool steel with ceramic inserts

ÇİÇEK A., KARA F., KIVAK T., EKİCİ E.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS , cilt.41, ss.461-469, 2013 (SCI-Expanded, Scopus)

49. ANN-based prediction of surface and hole quality in drilling of AISI D2 cold work tool steel

AKINCIOĞLU S., Mendi F., ÇİÇEK A., AKINCIOĞLU G.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY , cilt.68, ss.197-207, 2013 (SCI-Expanded, Scopus)

50. Artificial neural network based modelling of performance of a beta-type Stirling engine

Özgören Y. Ö., Çetinkaya S., Saridemir S., Çiçek A., Kara F.

Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering , cilt.227, sa.3, ss.166-177, 2013 (SCI-Expanded, Scopus)

51. Prediction of Damage Factor in end Milling of Glass Fibre Reinforced Plastic Composites Using Artificial Neural Network

ERKAN Ö., Isik B., ÇİÇEK A., KARA F.

APPLIED COMPOSITE MATERIALS , cilt.20, sa.4, ss.517-536, 2013 (SCI-Expanded, Scopus)

52. Predictive modeling of performance of a helium charged Stirling engine using an artificial neural network

ÖZGÖREN Y. Ö., Cetinkaya S., SARIDEMİR S., ÇİÇEK A., KARA F.

ENERGY CONVERSION AND MANAGEMENT , cilt.67, ss.357-368, 2013 (SCI-Expanded, Scopus)

53. Prediction of engine performance and exhaust emissions for gasoline and methanol using artificial neural network

Cay Y., Korkmaz I., ÇİÇEK A., KARA F.

ENERGY , cilt.50, ss.177-186, 2013 (SCI-Expanded, Scopus)

54. Machinability of AISI 316 Austenitic Stainless Steel With Cryogenically Treated M35 High-Speed Steel Twist Drills

ÇİÇEK A., UYGUR İ., KIVAK T., ÖZBEK N. A.

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME , cilt.134, sa.6, 2012 (SCI-Expanded, Scopus)

55. Modelling of thrust forces in drilling of AISI 316 stainless steel using artificial neural network and multiple regression analysis

Çiçek A., Kivak T., Samtaş G., Çay Y.

Strojniski Vestnik/Journal of Mechanical Engineering , cilt.58, ss.492-498, 2012 (SCI-Expanded, Scopus)

56. Taguchi method based optimisation of drilling parameters in drilling of AISI 316 steel with PVD monolayer and multilayer coated HSS drills

Kivak T., Samtaş G., Çiçek A.

Measurement: Journal of the International Measurement Confederation , cilt.45, sa.6, ss.1547-1557, 2012 (SCI-Expanded, Scopus)

57. Prediction of engine performance for an alternative fuel using artificial neural network

Çay Y., Çiçek A., Kara F., SAĞIROĞLU S.

Applied Thermal Engineering , cilt.37, ss.217-225, 2012 (SCI-Expanded, Scopus)

58. Application of taguchi method for surface roughness and roundness error in drilling of AISI 316 stainless steel

Çiçek A., Kivak T., Samtas G.

Strojniski Vestnik/Journal of Mechanical Engineering , cilt.58, sa.3, ss.165-174, 2012 (SCI-Expanded, Scopus)

59. Performance of cryogenically treated M35 HSS drills in drilling of austenitic stainless steels

Çiçek A., KIvak T., Uygur I., Ekici E., Turgut Y.

International Journal of Advanced Manufacturing Technology , cilt.60, ss.65-73, 2012 (SCI-Expanded, Scopus)

60. Tool life and wear mechanism of coated and uncoated Al 2O 3/TiCN mixed ceramic tools in turning hardened alloy steel

Aslantas K., Ucun T., çicek A.

Wear , ss.442-451, 2012 (SCI-Expanded, Scopus)

61. Parametric gear wheel applications in computer aided design Bi•lgi•sayar destekli• tasarimda parametri•k di•şli• çark uygulamalari

Ayyildiz M., Çiçek A., Kara F.

Journal of the Faculty of Engineering and Architecture of Gazi University , cilt.25, sa.3, ss.643-651, 2010 (SCI-Expanded, Scopus, TRDizin)

62. Recognition of 3d machining features using feature matrices Unsur matri̇sleri̇ kullanarak 3 boyutlu i̇şleme unsurlarinin taninmasi

Çiçek A., Aslantaş K.

Journal of the Faculty of Engineering and Architecture of Gazi University , cilt.25, sa.1, ss.147-155, 2010 (SCI-Expanded, Scopus, TRDizin)

63. Tool wear mechanism in interrupted cutting conditions

Sayit E., Aslantas K., Çiçek A.

Materials and Manufacturing Processes , cilt.24, sa.4, ss.476-483, 2009 (SCI-Expanded, Scopus)

64. Similarity and scaling assessments of mechanical parts using adjacency relation matrices

Çiçek A.

Journal of Materials Processing Technology , cilt.206, ss.106-119, 2008 (SCI-Expanded, Scopus)

65. Expert system based identification and extraction of detailed dimensions for gears Di̇cli̇leri̇n uzman si̇stem tabanli tanimlanmasi ve detayli boyutlarinin çikarilmasi

Çiçek A.

Journal of the Faculty of Engineering and Architecture of Gazi University , cilt.23, sa.3, ss.709-717, 2008 (SCI-Expanded, Scopus, TRDizin)

66. A part recognition based computer aided assembly system

Çiçek A., Gülesin M.

Computers in Industry , cilt.58, ss.733-746, 2007 (SCI-Expanded, Scopus)

67. The developing of computer aided part recognition system and implementation into engine assembly Bi̇lgi̇sayar destekli̇ parça tanima si̇stemi̇ ni̇n geli̇şti̇ri̇lmesi̇ ve motor montajina uygulanmasi

Çiçek A., Gülesín M.

Journal of the Faculty of Engineering and Architecture of Gazi University , cilt.22, sa.3, ss.313-323, 2007 (SCI-Expanded, Scopus, TRDizin)

68. A survey on assembly planning approaches Montaj planlama yaklaşimlari üzeri̇ne bi̇r araştirma

Çiçek A., Gülesin M.

Journal of the Faculty of Engineering and Architecture of Gazi University , cilt.22, sa.2, ss.255-268, 2007 (SCI-Expanded, Scopus, TRDizin)

69. Developing of a computer aided part recognition approach for CAD/CAM applications BDT/BDİ uygulamalari i̇çi̇n bi̇lgi̇sayar destekli̇ parça tanima yaklaş̧iminin geli̇şti̇ri̇lmesi̇

Çiçek A., Gülesin M.

Journal of the Faculty of Engineering and Architecture of Gazi University , cilt.22, sa.2, ss.237-246, 2007 (SCI-Expanded, Scopus, TRDizin)

70. Step based geometric and topological similarity assessment of mechanical parts

Çiçek A.

Mathematical and Computational Applications , cilt.12, sa.3, ss.141-150, 2007 (SCI-Expanded, Scopus, TRDizin)

71. Automatic reconstruction of 3D solid models from 2D drawings 2 Boyutlu çi̇zi̇mlerden 3 boyutlu kati modelleri̇n otomati̇k elde edi̇lmesi̇

Çiçek A., Gülesin M.

Journal of the Faculty of Engineering and Architecture of Gazi University , cilt.20, sa.3, ss.387-394, 2005 (SCI-Expanded, Scopus, TRDizin)

72. Reconstruction of 3D models from 2D orthographic views using solid extrusion and revolution

Çiçek A., Gülesin M.

Journal of Materials Processing Technology , cilt.152, sa.3, ss.291-298, 2004 (SCI-Expanded, Scopus)

Hakemli Bilimsel Toplantılarda Yayımlanmış Bildiriler 23

1. Improvement of Machining Processes: A Case Study

GÖKÇE H., YEŞİLAY R., UÇAK N., TEKE A., ÇİÇEK A.

7th International Symposium on Innovative Technologies in Engineering and Science (ISITES 2019), 22 - 24 Kasım 2019, ss.634-641, (Tam Metin Bildiri)

2. Sert Tornalama İşleminde İçten Kriyojenik Soğutmanın Yüzey Pürüzlülüğü ve Kalıntı Gerilmelere Etkileri

ÇETİNDAĞ H. A., ÇİÇEK A., UÇAK N.

7th International Symposium on Innovative Technologies in Engineering and Science (ISITES 2019), 22 - 24 Kasım 2019, ss.798-805, (Tam Metin Bildiri)

3. Performance of CBN Inserts in CO2 Assisted Hard Turning of AISI 52100 Bearing Steel

Çetindağ H. A., ÇİÇEK A., UÇAK N.

4th International Mediterranean Science and Engineering Congress (IMSEC 2019), 25 - 27 Nisan 2019, (Tam Metin Bildiri)

4. Finite element simulations of cutting force, torque, and temperature in drilling of Inconel 718

Uçak N., Çiçek A., Oezkaya E., Aslantas K.

17th CIRP Conference on Modelling of Machining Operations, CIRP CMMO, Sheffield, Birleşik Krallık, 13 - 14 Haziran 2019, cilt.82, ss.47-52, (Tam Metin Bildiri)

5. Tool performance analysis under different conditions in high speed turning of Ti6Al4V alloy

UÇAK N., ASLANTAŞ K., ÇİÇEK A.

9th International Congress on Machining, 8 - 10 Kasım 2018, (Tam Metin Bildiri)

6. The effects of cooling/lubrication techniques on cutting performance in micro-milling of Inconel 718 superalloy

ASLANTAŞ K., ÇİÇEK A.

8th CIRP Conference on High Performance Cutting (HPC 2018), 25 - 27 Haziran 2018, (Tam Metin Bildiri)

7. High speed turning of Ti6Al4V alloy in micro cutting conditions

ASLANTAŞ K., ÇİÇEK A.

8th CIRP Conference on High Performance Cutting (HPC 2018), 25 - 27 Haziran 2018, (Tam Metin Bildiri)

8. Evaluation of the effects of different menufacturing methods on tensile properties of S700MC steel

SEVİNÇ B., YAVUZ A., YILMAZ M. M., ÇETİN B., UÇAK N., ÇİÇEK A.

Metal 2018, 23 - 25 Mayıs 2018, (Tam Metin Bildiri)

9. Evaluation of the effects of different manufacturing methods on tensile properties of S700MC steel

Sevinc B., Yavuz A., Yilmaz M. M., Cetin B., Ucak N., Cicek A.

27th International Conference on Metallurgy and Materials, METAL 2018, Brno, Çek Cumhuriyeti, 23 - 25 Mayıs 2018, ss.584-590, (Tam Metin Bildiri)

10. Investigation of the Effects of Cold Treatment on Wear Performance of AISI 8620 Carburized Steel

UÇAK N., ÇİÇEK A., AYVALI K., AĞCA S., ORHAN S.

8th International Advanced Technologies Symposium (IATS17), Elazığ, Türkiye, 19 - 22 Ekim 2017, (Tam Metin Bildiri)

11. Evaluation of the Hole Quality in Drilling of Inconel 718 Under Cryogenic Conditions

UÇAK N., ÇİÇEK A.

8th International Advanced Technologies Symposium (IATS17), Elazığ, Türkiye, 19 - 22 Ekim 2017, (Tam Metin Bildiri)

12. AISI 316 çeliğinin kriyojenik işlem uygulanmış TiCN kaplı takımlarla işlenmesinde kesme şartlarının optimizasyonu

ALTAN ÖZBEK N., ÇİÇEK A., GÜLESİN M., ÖZBEK O.

International academic research congress (INES 2107), Antalya, Türkiye, 18 - 21 Ekim 2017, ss.1200-1208, (Tam Metin Bildiri)

13. Inconel 718 Süperalaşımının Delinmesinde Kriyojenik Soğutmanın Kesme Performansı Üzerine Etkilerinin Araştırılması

UÇAK N., ÇİÇEK A.

8th International Symposium on Machining (UTIS 2017), Antalya, Türkiye, 2 - 04 Kasım 2017, (Tam Metin Bildiri)

14. Talaşlı İmalat Süreçlerinde Kriyojenik Soğutma Uygulamaları Üzerine Bir Araştırma

UÇAK N., ÇİÇEK A.

5th International Symposium on Innovative Technologies in Engineering and Science (ISITES2017), Baku, Azerbaycan, 29 Eylül - 01 Ekim 2017, (Tam Metin Bildiri)

15. Takım çeliklerinin kriyojenik işlemi

ÇETİN A., ÇİÇEK A.

4th International Symposium on Innovative Technologies in Engineerin and Science (ISITES 2016 ), Antalya, Türkiye, 3 - 05 Kasım 2016, ss.922-931, (Tam Metin Bildiri)

16. AISI 316 çeliğinin tornalanmasinda kaplamali karbür takimlara uygulanan kriyojenik işlemin takim aşinmasi ve yüzey pürüzlülüğü üzerine etkileri

ALTAN ÖZBEK N., ÇİÇEK A., GÜLESİN M., ÖZBEK O.

7th International Symposium On Machining (UTIS 2016), İstanbul, Türkiye, 3 - 05 Kasım 2016, ss.233-240, (Tam Metin Bildiri) Sürdürülebilir Kalkınma

17. Mikro işlemede takım aşınması kanal geometrisi ilişkisi üzerine deneysel bir çalışma

ASLANTAŞ K., ÇELİK S. G., ÇİÇEK A., UCUN İ.

7th International Symposium on Machining (UTİS 2016), İstanbul, Türkiye, 3 - 05 Kasım 2016, ss.155-165, (Tam Metin Bildiri) Sürdürülebilir Kalkınma

18. Investigation of the effects of holding times at cryogenic temperatures on surface roughness and cutting forces in machining of stainless steel

ALTAN ÖZBEK N., ÇİÇEK A., GÜLESİN M., ÖZBEK O.

17. Uluslararası Makina Tasarım ve İmalat Kongresi, Bursa, Türkiye, 12 - 15 Temmuz 2016, (Tam Metin Bildiri)

19. Performance evaluation of S700MC and ST52 steels in terms of mechanical properties and fatique life

USTA T., ÇİÇEK A., UÇAK N., ÇELİK V., AĞCA S.

Metal 2016, Brno, Çek Cumhuriyeti, 25 - 27 Mayıs 2016, (Tam Metin Bildiri)

20. Kriyojenik işlem uygulanmış kaplamasız WC Co takımlarla AISI 304 paslanmaz çeliğin işlenmesinde yüzey pürüzlülüğü ve kesme kuvvetlerinin incelenmesi

ALTAN ÖZBEK N., ÇİÇEK A., GÜLESİN M., ÖZBEK O.

1st International Conference on Engineering Technology and Applied Sciences (ICETAS 2016), AFYONKARAHİSAR, Türkiye, 21 - 22 Nisan 2016, ss.1185-1191, (Tam Metin Bildiri)

21. Performance evaluation of a hybrid cooling-lubrication system in micro-milling of Ti6Al4V alloy

Aslantas K., Cicek A., Ucun I., Percin M., Hopa H. E.

7th CIRP Conference on High Performance Cutting (HPC), Chemnitz, Almanya, 31 Mayıs - 02 Haziran 2016, cilt.46, ss.492-495, (Tam Metin Bildiri)

22. PERFORMANCE EVALUATION OF S700MC AND ST52 STEELS IN TERMS OF MECHANICAL PROPERTIES AND FATIGUE LIFE

Usta T., ÇİÇEK A., UÇAK N., ÇELİK V., AĞCA S.

25th Anniversary International Conference on Metallurgy and Materials (METAL), Brno, Çek Cumhuriyeti, 25 - 27 Mayıs 2016, ss.549-554, (Tam Metin Bildiri)

23. Performance Evaluation of Cryogenically Treated Cu Cr Zr Alloy Electrodes in Electro Discharge Machining of AISI P20 Tool Steel

Çetin A., Çakır G., Uçak N., Çiçek A.

3RD INTERNATIONAL SYMPOSIUM ON INNOVATIVE TECHNOLOGIES IN ENGINEERING AND SCIENCE, Valencia, İspanya, 3 - 05 Haziran 2015, ss.662-669, (Tam Metin Bildiri)

Metrikler

Yayın

Yayın (Scopus)

Atıf (Scopus)

3284

H-İndeks (Scopus)

Atıf (Scholar)

499

H-İndeks (Scholar)

Proje

Tez Danışmanlığı

Açık Erişim

BM Sürdürülebilir Kalkınma Amaçları

Yayınlar & Eserler

Yayın

Yayın (Scopus)

Atıf (Scopus)

H-İndeks (Scopus)

Atıf (Scholar)

H-İndeks (Scholar)

Proje

Tez Danışmanlığı

Açık Erişim